Gateway Ultra2 Uživatelský manuál Strana 5
- Strana / 112
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
- ADAC Ultra2 S466 1
- Single Ended and Low 1
- Voltage Differential SCSI 1
- PCI RAID Controller 1
- Hardware Guide 1
- Revision History 2
- Table of Contents 3
- Contents 5
- Preface vii 7
- # of Physical 9
- Physical Device Layout 10
- Preface, Continued 12
- FCC Regulatory Statement 13
- Disclaimer 14
- 1 Overview 15
- • a single ended bus and 16
- Documentation 17
- 2 Introduction to RAID 19
- In This Chapter 20
- RAID Overview 22
- Consistency Check 22
- Fault Tolerance 22
- Disk Striping 23
- Disk Spanning 24
- Disk Mirroring 25
- Hot Spares 27
- Disk Rebuild 28
- Logical Drive 29
- Hot Swap 29
- SCSI Drive States 30
- Logical Drive States 30
- Disk Array Types 31
- Enclosure Management 31
- 3 RAID Levels 33
- Selecting a RAID Level 34
- Chapter 3 RAID Levels 35
- RAID 3, Continued 38
- 4 ADAC Ultra2 S466 Features 43
- Hardware Requirements 44
- Configuration Features 44
- Array Performance Features 45
- RAID Management Features 46
- Fault Tolerance Features 46
- Software Utilities 47
- PCI Bridge/CPU 49
- Cache Memory 49
- ADAC Ultra2 S466 BIOS 49
- Onboard Speaker 50
- Serial Port 50
- SCSI Bus 50
- SCSI Connectors 51
- SCSI Termination 51
- SCSI Firmware 51
- RAID Management 52
- Fault-Tolerance Features 53
- Compatibility 54
- 5 Configuring ADAC Ultra2 55
- Current Configuration 56
- Logical Drive Configuration 56
- Configuring Arrays 59
- Configuration Strategies 60
- Assigning RAID Levels 62
- Configuring Logical Drives 62
- Optimizing Data Storage 63
- Array Configuration Planner 65
- 6 Hardware Installation 67
- Installation Steps 68
- Step 1 Unpack 69
- Step 2 Power Down 69
- Step 3 Configure Motherboard 69
- Step 4 Install Cache Memory 70
- Step 5 Set Jumpers 72
- ADAC Ultra2 S466 Card Layout 72
- Step 5 Set Jumpers, Continued 73
- Step 6 Set Termination 75
- SCSI Termination, Continued 77
- Step 8 Connect SCSI Cables 80
- Step 9 Set Target IDs 81
- Step 10 Power Up 83
- Step 11 Run ADAC BIOS Setup 84
- DEVICE=C:\ADACDROM.SYS 85
- MSCDEX /D:MSCD001 85
- 7 Troubleshooting 87
- Firmware Initializing 88
- BIOS Boot Error Messages 89
- Other BIOS Error Messages 91
- Other Potential Problems 93
- Chapter 7 Troubleshooting 95
- A SCSI Cables and 97
- Connectors 97
- AMP - 786090-7 98
- 68 Conductor 0.025 Centerline 98
- Continued 100
- B Audible Warnings 107
Související produkty a manuály pro Brány / ovladače Gateway Ultra2
(6 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce